12/26/2011 7:58:59 AM
Topic:
GE psc25msta ss
bishopenterprise@gmail.com
Posts: 1
|
First I must know whether the unit is actually going into defrost and what measure you have taken to determine this. There are other reasons why your refrigerator would not run for 2 to 3 days. You will need to run down the conditions in steps. Are there lights on when refrigerator is not running? When it is running does the fresh food control affect compressor operation? Have you noticed any humming followed by click? Is the compressor hot- too hot to touch? Are your condenser coils blocked?danhaan27@msn.com wrote:
The freezer is staying in defrost mode for a couple of days and then goes back to normal for 3 days
|
|
|
10/27/2011 4:28:06 AM
Topic:
How do I post a topic in a forum?
gregaguilar@verizon.net
Posts: 1
|
ge front load washer not drying towels enough on spin cycle checked drin pump motr control replaced pressure switch replaced water valve replaced to no avial
|
|
|
10/25/2011 4:39:49 AM
Topic:
GE psc25msta ss
Collinsworh Appliance
Posts: 4
|
This unit doesn't have a mechanical defrost timer that will get stuck in defrost like the older ones will. Do you do anything to get it working again after it stops?
danhaan27@msn.com wrote:
The freezer is staying in defrost mode for a couple of days and then goes back to normal for 3 days
|
|
|
10/24/2011 11:37:22 PM
Topic:
GE psc25msta ss
danhaan27@msn.com
Posts: 1
|
The freezer is staying in defrost mode for a couple of days and then goes back to normal for 3 days
|
|
|
10/16/2011 7:59:05 PM
Topic:
burned drain solenoid
Scottgna@hotmail.com
Posts: 1
|
You need a whole pump assembly and you need to find out why the solenoid burnt up for the second time. You might need a new timer or control board.
|
|
|
10/3/2011 11:12:23 AM
Topic:
dryer vent lint
elm9613
Posts: 1
|
best way is to dissassemble the dryer cabinet and get to the blower, once there take compressed air and blow it out.; you will be surprised how much lint and dust comes out of dryer.
|
|
|
9/20/2011 9:43:58 AM
Topic:
Kenmore 400 Washer - Won't Fill
Collinsworh Appliance
Posts: 4
|
Could you provide a model number so we may see what we are dealing with?
Just from the info you have given, it could be your water level switch, something blocking the pressure hose, or a bad timer. If you can provide a model number and more detailed info on what is happening (the washer won't spin, etc.), I'm sure we can get it figured out for you.
Thanks,
|
|
|
9/20/2011 5:21:09 AM
Topic:
support bracket kit to repair evaporator
Collinsworh Appliance
Posts: 4
|
Do you have a model number?
|
|
|
9/20/2011 5:17:01 AM
Topic:
Thermador Electric Oven Selector Switch
Collinsworh Appliance
Posts: 4
|
It appears most parts have been discontinued for this model number. Sorry
|
|
|
9/10/2011 8:33:05 AM
Topic:
Thermador Electric Oven Selector Switch
BarryJB@Aol.com
Posts: 1
|
Need a Thermador electric overn selector switch. Model #: WO-18A
Any assistance will be appreciated!
|
|
|
8/11/2011 7:47:42 AM
Topic:
support bracket kit to repair evaporator
jjohnson4@pdq.net
Posts: 1
|
there is a kit ro repair a broken capillary channel bracket for the Thermostat sensor, November of 2005, I can't find the part number of this kit. It is still availible
|
|
|
7/19/2011 11:48:01 AM
Topic:
Kenmore 400 Washer - Won't Fill
tachiini@gmail.com
Posts: 2
|
Jus tried a new water inlet valve and same symptoms.
Why only 1.3 - 2.0 volts though??
I am getting 120 at the wall outlet, and checked all wirings which seem to be intact and ok.
what could it be?
|
|
|
7/18/2011 6:25:22 AM
Topic:
Kenmore 400 Washer - Won't Fill
tachiini@gmail.com
Posts: 2
|
checked the screens and cleaned them. Took the hoses outside to garden hose and they were clean.
Grabbed the multimeter and checked the solenoids -
863 ohms (give or take)
1.1 volts
Don't hear the solenoid click/engage.
Bad water inlet valve? Not enough power going to it?
|
|
|
6/21/2011 7:05:48 AM
Topic:
lp gas conversion instructions for whirlpool cook
gas123@stx.rr.com
Posts: 1
|
GLS3665RS01 have kit , no instructions come with it. unit has 5 burners , kit has 4 parts 2 orfice and 2 jets
|
|
|
5/1/2011 10:18:20 AM
Topic:
burned drain solenoid
h.havins@yahoo.com
Posts: 2
|
G.E. D/W MOD. GSD2600G02CC
Couple weeks ago found drain solenoid burned. Plunger coated with plastic and out of solenoid. (probably should have been clue that there was more wrong than visible) Changed solenoid, checked operation, OK, got paid and left. Had to go back Fri. Same problem. Hmmm... Need to look further. Found drain valve shaft with side play and shaft seal leaked it wiggled.
Will new shaft seal fix it or do I need a whole pump assy?
|
|
|
5/1/2011 10:00:03 AM
Topic:
dryer vent lint
h.havins@yahoo.com
Posts: 2
|
where is this lint?
|
|
|
3/21/2011 9:20:30 AM
Topic:
Whirlpool FL washer
jgarcia@apdepot.com
Posts: 2
|
Looks like you checked everything but have you checked the drain pump? If the pump is clogged it wont drain out and it will confuse the machine and shut it off. No error code will be displayed... try checking and see what it does
|
|
|
3/15/2011 8:43:23 AM
Topic:
Whirlpool FL washer
brooksappl@msn.com
Posts: 1
|
GHW9400PW4 This machine stops in cycles like it is on pause and won't finish the cycle. Time is remaining on the display. Door latch, motor, CCU, MCU, control board, pressure control, flow meter, all check out. What is the problem? Nothing in tech help relates to this issue as there is NO error code.
|
|
|
3/14/2011 1:23:21 PM
Topic:
quick repair on refrigerator
motordog56@hotmail.com
Posts: 2
|
here a tip how to repair a separated cap and suction line when on field,by using plastic cable ties to keep both lines together.
|
|
|
3/14/2011 1:06:46 PM
Topic:
Whirlpool side by side ice machine/cold water
motordog56@hotmail.com
Posts: 2
|
cardenasken@yahoo.com wrote:
Whirlpool Model ED5FHGXKB02 TYPE 2555A DOM 05/02 Ice machine stopped working after 8 years. Water is available. Is there is simple test to run to assure that machine is sending the signal down to water valve? Water valve and ice machine water valve are the same component and water works fine.
it sound like normal ice makers usually last 8-10 years then one day they just die silent,but there you can test it,manually cycle it and check for any movement on dial if it moves but no water comes out water valve and ice maker are operable,{you already fix it }if not first thing unplug ice maker,using old ice maker cord,connect brown and black.{ignoring the rest }and see if water comes out that means valve is in good condition {ice maker die silent} replace unit. by testing water valve this way save you moving refrigerator out to check valve hope that tip help you amigo!!!! polo {h.c.appliances}
|
|
|