4/11/2013 6:24:08 AM
Topic:
Help us eat please! Frigidare Range, oven issues
kenny@globalpublishinginc.com
Posts: 1
|
My Frigidare electric oven will not stop heating up no matter what temp. it is set to. I tested the RTD which pokes through the back of the oven with my meter set to 2K. Meter read 1.083. Manual says should read 1000 ohms-1100 ohms. I also checked the bake and broil elements and got between 15-17 ohms which should be good. Any advice from anyone would sure help my family out. We unfortunately dont have the money to hire someone to come out to house or even buy another oven. My name is Kenny and Im in Jacksonville, FL.
|
|
|
1/30/2013 2:57:53 AM
Topic:
Help!!!!
csrepairservices@suddenlink.net
Posts: 1
|
I am working on a JennAir range M# SVE87600B. The clock would not keep time and we were getting apower relay board fault. I ordered and replaced the parts in question and the clock and oven are now functioning normally. However now the touch pad does not respond to ron the left side burners. I have cleaned the ribbon cable to no avail. I can manipulate the ribbon cable and get it to function intermittently but thats it. I swapped the left and right side burner controls and the control functions normally. Does anyone know any tricks to help resolve this issue? The touchpad is N.L.A. Part #71002649.... If someone has it in stock and is willing to part with it please let me know. Thanks.
|
|
|
9/24/2012 9:10:10 AM
Topic:
Whirlpool Dryer element not shutting off
Dusty Corgill
Posts: 2
|
I sent you an email to your inbox with the technicians sheet for you model attached. It should help you pinpoint the problem. Let me know if you have any questions. dcorgill@apdepot.com
|
|
|
9/20/2012 9:26:59 AM
Topic:
Whirlpool Dryer element not shutting off
Robert
Posts: 2
|
Thank you for getting back to me,
Yes, I have checked that and its all good there. I want to think its the sensor harnest or even one of the boards inside cabnet acting up. Have you heard of that being a problem?
|
|
|
9/20/2012 8:40:59 AM
Topic:
Whirlpool Dryer element not shutting off
Dusty Corgill
Posts: 2
|
Robert, have you taken your element out of the casing? Sounds like you have a grounded element. It could be that the coil has broken and welded itself to the metal casing, if so the element will continue to stay on all the time because it will bypass all the fuses and thermostats.
|
|
|
9/20/2012 4:38:09 AM
Topic:
Whirlpool Dryer element not shutting off
Robert
Posts: 2
|
We already changed out all sensors, thermo's, fuse and still element isn't shutting down. I have been looking and really can't pin point problem. Can anyone help me out.
Mod# WED9200SQ0
Thank you
|
|
|
7/26/2012 9:55:12 AM
Topic:
Fridgidaire evaporator problem
jerry@circlehranch.net
Posts: 1
|
The evaporator fan on my side by side model number GLR264ZAW0 isn't getting power. I've changed tha evaporator motor, the adaptive control board and the compressor capacitor, the three things suggested by repair guides. I also shorted out the freezer door switch, no luck. The compressor runs, the evaporator cools down, but no power to the evaporator fan. Someone please help, I'm about to go crazy.
|
|
|
12/26/2011 7:58:59 AM
Topic:
GE psc25msta ss
bishopenterprise@gmail.com
Posts: 1
|
First I must know whether the unit is actually going into defrost and what measure you have taken to determine this. There are other reasons why your refrigerator would not run for 2 to 3 days. You will need to run down the conditions in steps. Are there lights on when refrigerator is not running? When it is running does the fresh food control affect compressor operation? Have you noticed any humming followed by click? Is the compressor hot- too hot to touch? Are your condenser coils blocked?danhaan27@msn.com wrote:
The freezer is staying in defrost mode for a couple of days and then goes back to normal for 3 days
|
|
|
10/27/2011 4:28:06 AM
Topic:
How do I post a topic in a forum?
gregaguilar@verizon.net
Posts: 1
|
ge front load washer not drying towels enough on spin cycle checked drin pump motr control replaced pressure switch replaced water valve replaced to no avial
|
|
|
10/25/2011 4:39:49 AM
Topic:
GE psc25msta ss
Collinsworh Appliance
Posts: 4
|
This unit doesn't have a mechanical defrost timer that will get stuck in defrost like the older ones will. Do you do anything to get it working again after it stops?
danhaan27@msn.com wrote:
The freezer is staying in defrost mode for a couple of days and then goes back to normal for 3 days
|
|
|
10/24/2011 11:37:22 PM
Topic:
GE psc25msta ss
danhaan27@msn.com
Posts: 1
|
The freezer is staying in defrost mode for a couple of days and then goes back to normal for 3 days
|
|
|
10/16/2011 7:59:05 PM
Topic:
burned drain solenoid
Scottgna@hotmail.com
Posts: 1
|
You need a whole pump assembly and you need to find out why the solenoid burnt up for the second time. You might need a new timer or control board.
|
|
|
10/3/2011 11:12:23 AM
Topic:
dryer vent lint
elm9613
Posts: 1
|
best way is to dissassemble the dryer cabinet and get to the blower, once there take compressed air and blow it out.; you will be surprised how much lint and dust comes out of dryer.
|
|
|
9/20/2011 9:43:58 AM
Topic:
Kenmore 400 Washer - Won't Fill
Collinsworh Appliance
Posts: 4
|
Could you provide a model number so we may see what we are dealing with?
Just from the info you have given, it could be your water level switch, something blocking the pressure hose, or a bad timer. If you can provide a model number and more detailed info on what is happening (the washer won't spin, etc.), I'm sure we can get it figured out for you.
Thanks,
|
|
|
9/20/2011 5:21:09 AM
Topic:
support bracket kit to repair evaporator
Collinsworh Appliance
Posts: 4
|
Do you have a model number?
|
|
|
9/20/2011 5:17:01 AM
Topic:
Thermador Electric Oven Selector Switch
Collinsworh Appliance
Posts: 4
|
It appears most parts have been discontinued for this model number. Sorry
|
|
|
9/10/2011 8:33:05 AM
Topic:
Thermador Electric Oven Selector Switch
BarryJB@Aol.com
Posts: 1
|
Need a Thermador electric overn selector switch. Model #: WO-18A
Any assistance will be appreciated!
|
|
|
8/11/2011 7:47:42 AM
Topic:
support bracket kit to repair evaporator
jjohnson4@pdq.net
Posts: 1
|
there is a kit ro repair a broken capillary channel bracket for the Thermostat sensor, November of 2005, I can't find the part number of this kit. It is still availible
|
|
|
7/19/2011 11:48:01 AM
Topic:
Kenmore 400 Washer - Won't Fill
tachiini@gmail.com
Posts: 2
|
Jus tried a new water inlet valve and same symptoms.
Why only 1.3 - 2.0 volts though??
I am getting 120 at the wall outlet, and checked all wirings which seem to be intact and ok.
what could it be?
|
|
|
7/18/2011 6:25:22 AM
Topic:
Kenmore 400 Washer - Won't Fill
tachiini@gmail.com
Posts: 2
|
checked the screens and cleaned them. Took the hoses outside to garden hose and they were clean.
Grabbed the multimeter and checked the solenoids -
863 ohms (give or take)
1.1 volts
Don't hear the solenoid click/engage.
Bad water inlet valve? Not enough power going to it?
|
|
|